dbx driverack 260 manual download

File Name:dbx driverack 260 manual download.pdf
Size:3033 KB
Type:PDF, ePub, eBook, fb2, mobi, txt, doc, rtf, djvu
Category:Book
Uploaded18 May 2019, 17:11 PM
InterfaceEnglish
Rating4.6/5 from 581 votes
StatusAVAILABLE
Last checked9 Minutes ago!

dbx driverack 260 manual download

The 260 capitalizes on the road tested and contractor approved nature of the other products in the DriveRack line. The 260 provides full bandpass and crossover configurations as well as independent output processing and a full time RTA for live sound applications. The DriveRack 260 continues the legacy of DriveRack series, which has been created by the company that has been redefining the standard of signal processing for more than 30 years. The DriveRack 260 was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface.XLR RTA Mic input It runs on phantom power (supplied by the Driverack units) and comes with a clip and case. With the DriveRack 260, dbx Professional Products has redefined the standard by which all other loudspeaker management processors will be compared. The DriveRack 260 was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface. For more information, please visit: www.driverack. com or www.dbxpro.com. This manual will be your guide to understanding the full functionality of the powerful DriveRack 260. By combining the different components, the configuration possibilities are limitless. After you have become familiar with the unit, we encourage you to experiment and find the most effective and efficient way to run your system by utilizing the powerful processing of the DriveRack 260. 0.1 Defining the DriveRack 260 System The dbx DriveRack 260 is the most effective way to manage all aspects of post mixer processing and signal routing. The DriveRack 260 essentially becomes the only device that you will need between the mixer and the power amps. The following are just some of the features of the DriveRack 260. Please do not offer the downloaded file for sell only use it for personal usage. Looking for other manual. Document preview No preview for this item!For this no need registration.http://concretosmecanicos.com/nbloom/fckuploads/cryptography-and-network-security-principles-and-practice-6th-edition-solution-manual.xml

May be help you to repair. You could suffer a fatal electrical shock. Instead, contact your nearest service center. Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, Also some files are djvu so you need djvu viewer to open them. These free programs can be found on this page: needed progs If you use opera you have to disable opera turbo function to download file. If you cannot download this file, try it with CHROME or FIREFOX browser. Translate this page: Relevant AUDIO forum topics: AB osztalyu erositok kimeno emitter ellenallasa Sziasztok! Azt tudom, hogy milyen megfontolasokkal alakitjak ki a kulonbozo fokozatokat az erositokben, am a leirasokban mindig a vegere hagyjak a teljesitmeny fokozatot es allandoan elsikkad az emitter ellenallasok kerdese, sose lattam magyarazatot, hogy az adott erositoben miert pont akkora az emitter ellenallas erteke (a teljesitmenyt ertem). En szerencses tulajdonosanak mondhatom magam egy (azaz ket) ilyen hangfal-erositonek ( ) ebben pl.Tehat miert jo az erositoben az emitter ellenallas egyaltalan, azt leszamitva, hogy zarlat vedelemnek hasznaljak a rajta eso feszultseget.Panasonic SA HT-870 hazimozi rendszerhez keresek kapcsolasi rajzot, vagy segitseget. Egy autoradioban csereltem vegfokot, TA8276H helyett raktam be TDA7560-at. Szol, de csunyan, a hid kimenete el van billenve, az egyiken 1V korul, a masikon 6,5V, mindez 11,8V-os tapfesznel. Van otletetek? Eg Merci radioban van, 3 retegu nyak, de a bemenetek szerintem biztos le vannak valasztva kondival.Udv: Jacint Home made erositon csak a negativ hangresz van benne Sziasztok! Egy hasonlo rajzot talaltam a neten, de nalam a Q7 bazisan -37V van.You can write in English language into the forum (not only in Hungarian). Waiting For Flash Download OF161000 faced How to solve this type of problems? Can you explain some ideas?http://dumainfotech.com/userfiles/cryptography-and-network-security-principles-and-practice-4th-edition-solution-manual.xml

It seems like before flashing it is necessary to reset it to the factory settings otherwise the flash memory is full and gives an error. Check your email again and check your spam filters. If you want to get involved, click one of these buttons! Powered by Vanilla Forums. Dbx took the dominant DriveRack 260, improved its features, and added more. The result is dbx’s first-ever, 3 input, 6 output Loudspeaker Management processor. See All 14 Rows On Dbxpro.com DriveRack 260, Free Download by DBX. A tool that helps ensure that your hard drive is running optimally. See All 14 Rows On Dbxpro.com Full text of ' dbx DriveRack 260 Firmware Update Procedure If you are using a USB to Serial adapter it is recommended that you ensure proper connection before performing the update. We recommend installing the version of DriveWare that came with your device. Once a connection has been confirmed, uninstall DriveWare then continue with the below steps. Go here for more information on these USB to Serial converters. Go here for information on troubleshooting your USB to Serial Converter. Go to the dbx downloads page: 2. Download the latest 260 Updater. Download DriveWare if you intend to use it in conjunction with the 260 (it is recommend to use the latest version of DriveWare in conjunction with the latest version of the 260 firmware). Install the Firmware Updater. To install the updater: Click on the downloaded EXE file. Read contents then, Click Next. NullsoFt Install System v2.24 Cancel Make sure that “Desktop Shortcuts” is checked. If you would like to select a different location for installation, do so here. If you are unsure, leave the settings as they are. Click Install. Leave these items checked.Would you like to try it too? Please try again later. Page 2 and 3: Read contents then, Click Next Make Page 4 and 5: Read contents of document. Installa Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible.

Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner’s manual. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage. If the attachment plug needs to be changed, refer servicing to qualified service personnel who should refer to the table below.Severe injury or death can then result if the chassis and earth ground are touched simultaneously. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. For rack-mount or installation where plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building. Connect this equipment only to the power source indicated on the equipment rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel or equivalent.

Operation is subject to the following two conditions: Discard the mains plug at a suitable disposal facility.Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and MUST be ASTA approved to BS1362. For over 30 years, dbx has been the industry leader in With the DriveRack 260, dbx Professional Products has redefined the stan- For more information, please visit: www.driverack.com or The 260 DriveRack essentially becomes the only device that you will need between the mixer and the power amps.The ZC-2 provides programmable Volume and Mute control. The ZC-3 allows Program Selection on the 260. The ZC-4 also offers Program Selection via Contact Closure inputs for Room Combining applications. The ZC-BOB was created to accommodate “home-run” or parallel wiring to the unit. With a maximum length of 5,000 ft., the Zone Controllers offer a simple way to create a simple yet elegant solution to many installation applications. Be prepared to accurately describe the problem. Know the serial number of your unit - this is printed on a sticker attached to the top panel. If you have not already taken the time to fill out your warranty registration card and send it in, please do so now. Make sure you have correctly followed installation steps and operation procedures. If you are still unable to solve a problem, contact our Customer Service Department at (801) 568-7660 for consultation. If you need to return a product to the factory for service, you MUST contact Customer Service to obtain a Return Authorization Number. After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the factory service facility. In all cases, you are responsible for transportation charges to the factory.Mark the package with the name of the shipper and with these words in red: DELICATE INSTRUMENT, FRAGILE. Insure the package properly. Ship prepaid, not collect. Do not ship parcel post.

Proof-of-purchase is considered to be the burden of the consumer. A Return Authorization number must be obtained from dbx by telephone. The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly. In no event shall dbx or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. An IEC cord is included. EU version accepts 220V-240V at frequencies from 50Hz-60Hz. Note: dbx Professional Products recommends that power amplifiers connected to the DriveRack 260, should be powered down prior to cycling the power on the DriveRack 260. The display will also notify the user if any internal clipping is taking place within the unit by displaying “CLIP” in the display. The functions of the aforementioned buttons are as follows: Successive presses will move you through the When pressed and held, the 260 When pressed and held, the 260 will enter METER mode. When pressed and held, the 260 will enter the PROGRAM DELETE module. When pressed and held, the 260 will enter the Wizard section which includes: SYSTEM SETUP, AFS and AUTO EQ WIZARD. These meters monitor the signal level right after the input module. The display provides you with a clear and concise overview of each aspect LCD Display - All operational information of the 260 DriveRack is displayed here. The display will also notify the user if any internal clipping is taking place within the unit. The following message will appear: CLIP. Data Wheel - The data wheel is used to scroll through the program menu of the 260 DriveRack. The Data Wheel is also used to perform editing functions to effects and utility menu features. Button Array - Operational editing is done using this 12 button array. A complete description of each button’s functionality is listed below.

Input meters - These two 6-segment LED meters monitor the input level of the 260 DriveRack directly after the input mixer. Output mutes - These six mute buttons are used to mute the output signal of the 260 DriveRack. Output meters - These six 6-segment meters monitor the output levels of the 260 DriveRack directly after the output gain stage. Threshold meters - These six 1-segment meters show that threshold level of the output dynamics has been exceeded. This feature of the 260 DriveRack allows for quick and accurate venue setups. The menu section of the Wizard offers System setup, Auto EQ and AFS (Advanced Feedback Suppression). The following will walk you through your venue setup. To select any one of the three options, rotate the wheel. If you are performing the System setup, press either the button or the wheel and the display will appear as follows: Once you have selected your input option, press the button and the display will appear as follows: Once you have selected your EQ option, press the button and the display will appear as follows: Once you have selected your Insert 1 module option, press the button and the display will appear as follows: Once you have selected your Insert 1 module option, press the button and the display will appear as follows: Once you have selected your Main speaker option, press the button and the display will appear as follows: Once you have selected your SUB speaker option, press the button and the display will appear as follows: Note that the top line of the display will either read High, Mid or Low depending on your selected speaker setup selections. Once you have selected your Amp tuning option (depending on the amp type), you will select the specified amplifier sensitivity setting if applicable. Once set, press the button, and you will now be given the option of optimizing your amp levels with the 260 DriveRack for.

The page will appear something like this: Note that based on your amp selection, the 260 DriveRack will initially display the recommended setting of that particular amp for obtaining maximum headroom. This is done to match unity gain from the 260 DriveRack and your amplifier. Note that if Sub Speakers are included in the speaker selection, you will be asked if the sub woofer is bridged or mono. For more information regarding Amplifier gain settings, please refer to the System Setup and Gain Structure information located in the appendix section. Amplifier parameters are used to set the limiters to stop amplifier clipping and balance out the crossover levels. You may find that you want to re-adjust the crossover levels based on your taste and type of music. The Auto EQ Wizard automatically adjusts the response of the system by producing pink noise and adjusting the Graphic EQ until the RTA matches a selected response. From the 260 DriveRack Wizard menu, rotate the wheel until the display appears as follows: Once you have selected your desired EQ Frequency response, press the button and the display will appear as follows: Connect an RTA-specific microphone to the rear-panel RTA mic input. Once the Pink level has been adjusted to the desired volume. The mic level indicator will register the signal level. Press the button and the Auto EQ sequence will begin. The display will either show the graphic EQ or the RTA. Rotating the wheel clockwise and counter clockwise will toggle between the two modes. You can also select either mode to default to in the Utility menu. Regardless, the display will appear something like this: If you are using independent left and right graphic EQs, you will auto EQ each side independently. If you are using a stereo-linked EQ, both sides will be EQ’d simultaneously. Auto EQ can be aborted at any point in the process by pressing the button.

Upon completion of the Auto EQ Wizard, you can return to program mode by releasing the button and pressing the button. The AFS Wizard will lead you through the setup of of the fixed filters of the AFS module. The fixed filter mode is designed to place notch filters as you introduce feedback by opening up your mics and slowly increasing the gain. Because the fixed mode is sensitive, it is important not to present an external music source such as CD player or other audio signal into the system. From the Wizard menu, rotate the wheel until the display appears as follows: This will range from values 0-12. Live and Fixed filter types differ in that FIXED mode filters are automatically assigned to a frequency creating feedback, thus remaining at that frequency until cleared by the user. In LIVE mode, live filters automatically detect and remove feedback frequencies in the presence of audio (music or speech). When all of the live filters have been used, they begin to round robin. Essentially this means that the first filter set is replaced where a new feedback is detected and notched out.Once the desired fixed number of filters has been selected, press the button and the display will read. A blocked out F or L indicates a filter that is set, or in use. Once the desired number has been selected, press the and the display will read: This means that a higher Q will produce a filter that is more narrow. To guarantee that feedback is suppressed at lower frequencies, the AFS may place wider notch filters at these lower frequencies (below 700 Hz). Once the desired fixed type has been selected, press the button and the display will read: Once the desired level has been set and all of the fixed filters have been assigned, the unit will automatically move you to the page that indicates the fixed filter setup has been completed.

If you have reached the performance level setting and all of the fixed filters have not been used, you may want to return Regardless, once you have completed the setup, the display will read: For more information regarding feedback elimination, please see the AFS parameters of the Detailed parameters section. The Data wheel is also used to change the values of the selected parameter by simply rotating the wheel. Pressing the Data wheel will toggle between the available parameters on any selected page of the currently selected effect module. This is the EQ section located prior to the crossover section. Successive presses will rotate through the various precrossover 28 band EQ and Post-xover PEQ section modules. Successive presses will move through each input and output. When pressed and held, you will enter Config mode. When pressed and held, the 260 will enter METER mode. From program mode, press the EQ button to reach the EQ module to be edited. Successive presses of the EQ button will move through each channel. From program mode, press the X-OVER button.Successive presses of the Other button will move you to each of the various insert modules available. Pressing the Data Wheel will select the effect parameter to be edited. Once you have reached the Dynamics module, Inf:1 Gain -20 to 20dB Pressing the Data Wheel will select the effect parameter to be edited. Pressing the Data Wheel will select the effect parameter to be edited. Pressing and holding the Utility button will enter you into the meter mennu. With the introduction of the new 260, the heritage of. The 260 capitalizes on the road Contractors will appreciate its control inputs for wall-panel logic control and The DriveRack 260 was designed with the This goal has been achieved by Graphic Equalizer, industry-standard dbx stereo compressor module, feedback These features XLR RTA Mic input Create an account and earn points for your reviews! Click for details.

Everyting you need bundled into one simple, tidy, portable package. Well, you may think your powered speaker system is complete, but you’re missing half the picture. DriveRack PX is the other half. In another dbx industry first, they’ve created a processor specifically tailored for powered speakers. Utilizing their highly-acclaimed DriveRack technology, the PX picks up where your powered speakers leave off. It even includes stereo or mono subwoofer support. With the included dbx M2 measurement mic, Auto-EQ corrects for audible deficiencies in the room environment. Your ears, your audience, and your powered speakers will forever thank you. Dbx’s exclusive Setup, Auto-EQ, and AFS Wizards, and out-of-the-box support for a host of JBL and other popular powered speakers, make setup a snap. Louder, cleaner, better sound than you thought possible from your powered speakers. Create one here. Creators are allowed to post content they produce to the platform, so long as they comply with our policies. United Kingdom. Company number 10637289. Our payment security system encrypts your information during transmission. We don’t share your credit card details with third-party sellers, and we don’t sell your information to others. Please try again.Please try again.Show details. Sold by TIGERSL and ships from Amazon Fulfillment. Sold by GreyBar and ships from Amazon Fulfillment. Please try your search again later.Now dbx tape noise reduction systems are used in professional recording studios around the world.The DriveRack products provide the tools that ensure that the system sounds its very best. The DriveRack 260 capitalizes on the road-tested and contractor-approved nature of the other products in the DriveRack line. The DriveRack 260 provides full bandpass and crossover configurations as well as independent output processing and a full-time RTA for live sound applications.

Contractors will appreciate its control inputs for wall-panel logic control and the patent-pending Advanced Feedback Suppression (AFS).Pattern Name: Processor The drive Rack products provide the tools that ensure that the system sounds its very best. The 260 capitalizes on the road tested and contractor approved nature of the other products in the drive Rack line. The 260 provides full Bandpass and crossover configurations as well as independent output processing and a full time RTA for live sound applications. Contractors will appreciate its control inputs for wall-panel Logic control and the patent-pending advanced feedback suppression (AFS). Pattern Name: Processor To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. Please try again later. PT 5.0 out of 5 stars The auto EQ does a decent job but does require further fine-tuning once applied. Luckily there is a built-in RTA, a graphic EQ, and parametric EQ which you can run in addition to auto EQ. So there's an electronic crossover, 3 EQs all in one small package. There's also subharmonic synth, compressor, limiter (which I don't use since my setup is home hi-fi, not live sound) but nice those options are available. After doing the auto EQ, I then learned I could bi-amp my speakers with Venu360. Now I can control the bass on my NHT Classic 4 speakers desperately. This venu360 has big advantages over something like a MiniDSP because you need NO SOFTWARE REQUIRED TO CONTROL IT. We use computers enough in our day-to-day lives.Suffice it to say however, the 260 model came highly recommended by a friend who does huge stage setups. I'm brand new to the DriveRack system, so this was a new experience for me, going from a rack full of gear to a single 1u device.

I started my introduction with the PA2 model, and immediately found a HUGE flaw in the circuit design that caused me to return it immediately. Upon inquiry, my buddy also informed me that he knew about that flaw and that is one reason he did not use the PA series. So, I tried the 260, the one he recommended. I love it. It's super easy to set up, does a huge pile of magic, and once it's all set up, it just works like a champ. So. if you're new to Drive Rack and not sure if this thing is for you, or if you're ready to step up to digital processing, give this one a try. You'll be up and running in less than 15 minutes. I'm kind of amazed how this one little box can be so quick to set up for my small rig, and still be fully functional for my buddy who does huge shows of 3-30k attendance. I have not yet had a chance to play with the WIZARD mode (using the RTA Mic). Next time I set up a production stage, I'm going to give that a try.This has really added value to our service at church. The quality and balance of the band has drastically improved and the clarity of the spoken word is a lot better than the basic equalizer we were using. It has a lot of features, most of which we aren't using, but I have been implementing some as I learn how they work. Be warned that this is a quite advanced piece of technology and isn't something most people off the street can just set up and use.I was originally going to purchase this through Sweetwater but found a better price on here with 2-day shipping. We have installed it in our new system and could not be more satisfied.All in one single component. Save space and connecting troubles with other processors. Very easy to manage and delivers excellent quality. The compressor is good and delivers what is needed. Very good solution and an affordable price.If you want sound quality that stands out this is what you needSorry, we failed to record your vote.

Please try again In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. If you are using a USB to Serial adapter it is recommended that you ensure proper connection We recommend installing the version of DriveWare that came with Go here for more information on these USB to Serial converters. Go here for information on troubleshooting your USB to Serial Converter. To install the updater. Click on the downloaded EXE file. Read contents then, Click Next Pre-install Instructions. Please read the following instructions before proceeding. It is highly recommended that you use DriveWare V2.6.2 with DriveRack 260 Make sure that “Desktop Shortcuts” is checked. Press Next. If you are unsure, leave Click Install. Leave these items checked. Click Finish. Completing the Drive Rack 260 Click Finish to close this wizard. Black Learn More (Opens in new window) Learn More (Opens in new window) Learn More (Opens in new window) Learn More (Opens in new window) Learn More (Opens in new window) Learn More (Opens in new window) Learn More (Opens in new window) Click To Read More About This Product Some exclusions apply. Questions? CallThe DriveRack 260 offers 2 independent channels of processing power with a linkable 28-band graphic EQ, industry-standard dbx stereo compressor module, feedback eliminator, and the 120A Subharmonic Synthesizer on the input signal path. 6-channel output system includes parametric EQs, PeakStopPlus limiters (to provide protection against speaker blowouts), and alignment delay. Setup Wizard gets you up and running quickly and GUI control provides easy PC-based control. Click on the PDF link below for more complete details on this powerful PA control system. Call or click to order now! All Rights Reserved.

Publisher does not accept liability for incorrect spelling, printing errors (including prices), incorrect manufacturer's specifications or changes, or grammatical inaccuracies in any product included in the Musician's Friend catalog or website. Prices subject to change without notice. You must have JavaScript enabled in your browser to utilize the functionality of this website. Cable Mike Cable Rack Cable Mike Cable Rack XLR RTA Mic input Use single quotes (') for phrases. We are distributor for many companies in India and having huge network of dealers and distributors all across the country. The experience of management and visionary has made our company one of the largest supplier in the field of audio visual and security Read More Opp. Orient Club,Near Gujrat College Ellisbidge,Ahmedabad,Gujarat 380006, India. All you need is an internet connection. We're here to help. For a specific manufacturer software download page please click on the logos on the left hand side to be redirected to the appropriate website.